ASTM D6413 EBOOK

ArcWear performs vertical flame testing for textiles in accordance with ASTM D which is used in ASTM F, ASTM F, and NFPA We will report. 23 Jul Some updates have been made to ASTM D Standard Test Method for Flame Resistance of Textiles (Vertical Test) commonly used in flame. ASTM D Test Method for Flame Resistance of Textiles. (Vertical Test). • Pass criteria: max char length of 10 cm. • After-flame of not more than 2 seconds.

Author: Akidal Tegar
Country: Malawi
Language: English (Spanish)
Genre: Health and Food
Published (Last): 1 August 2013
Pages: 22
PDF File Size: 9.6 Mb
ePub File Size: 9.48 Mb
ISBN: 349-6-33535-195-9
Downloads: 73098
Price: Free* [*Free Regsitration Required]
Uploader: Gadal

ASTM D6413: Vertical Flame Test for Flame Resistance of Textiles

The astm d6413 of melting or dripping, if any, is also astm d6413. Afterflame is the number of seconds during which there is a visible flame remaining on the fabric. It is the responsibility of the user of this standard to establish appropriate safety axtm health practices and determine the applicability of regulatory limitations prior to use.

July 10, at 9: Notify me of follow-up comments by email. Save my name, email, and astm d6413 in this browser for the next time I comment. The cut edge of the fabric on the bottom is exposed to a controlled methane flame for 12 seconds as seen in the image above, left. Tyndale performs voluntary safety auditing on Tyndale garment fabrics. The between-laboratory precision of this test method has not been established.

TOP Related Posts  ANSI ISA S84 01 EBOOK

If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration on the known bias. After exposure to the flame, afterflame, afterglow astm d6413 char length are measured: The test results from the two laboratories should be compared using a statistical test for astm d6413 data, at a probability level chosen prior to the testing series.

Refer to Section 14 astm d6413 single-laboratory precision. Historical Version s – view previous versions of standard. Combining values from the two systems may result in non-conformance with the standard. The purpose of this test is to determine whether a fabric will continue to burn after the source of ignition is removed.

The values stated in each system may not be exact equivalents; therefore, astm d6413 system shall be used independently of the other. We are Proud to Protect workers, and understand that our dedication to testing is astm d6413 atsm way to ensure that our garments perform as expected — every time!

ASTM D6413

Link to Active This link will always route to the current Active version of astm d6413 standard. The ASTM D test method is utilized to evaluate the flame resistance of every production lot of asm used in Tyndale-branded clothing.

ICS Number Code Notify me of new posts by email. Afterglow is the number of seconds during which there is a visible glow remaining astm d6413 the fabric. This is the defining astm d6413 method for compliance with OSHA Other materials with established test values may be aztm for this purpose.

TOP Related Posts  SHYAMCHI AAI BOOK IN PDF

Leave a Reply Cancel reply Your email address will not be published. Char Length is the length in inches of fabric destroyed by astm d6413 flame.

Adopted from Federal Test Standard No. Five tests astm d6413 performed and the results are averaged and reported as astm d6413 final test result. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

Compliance, ASTM D | Tingley®

Work Item s – proposed revisions of this standard. Garments that meet these standards are used to comply with: As a minimum, the test samples used should be as homogeneous as possible, that are drawn astm d6413 the material from which the disparate test results are obtained, and that are assigned randomly in equal numbers to each laboratory for testing. ASTM D is used to determine flame resistance of fabrics used to protect against both electric arc and flash fire hazards.

astm d6413

Your email address will not be published.