View and Download Lenze series operating instructions manual online. Inverter Drives Variant Dancer-position control with Torque control. series. vector. System/Component overview. Lenze. FU vector en 11/ 3. System overview/Selection guide. Communication modules e.g. keypad or. PROFIBUS. Get Lenze IB Manual. Get all Lenze manuals! with optical fibre cable together with the controller series as of E DC controller E 5x. 6x.

Author: Samujind Kazigrel
Country: Eritrea
Language: English (Spanish)
Genre: Automotive
Published (Last): 10 February 2017
Pages: 292
PDF File Size: 10.53 Mb
ePub File Size: 8.63 Mb
ISBN: 149-5-90061-306-9
Downloads: 92282
Price: Free* [*Free Regsitration Required]
Uploader: Daigrel

What’s missing? Tell us about it.

The inforrnation is identical with that under C, with the differente that you tan read the controller value directly thus excluding conversion errors. Data structure of user data Byte no. Controller type Controller type Min.

Here, the field frequency input via terminal 8 or via the digital frequency input or via code CO46 is used to limit the maximum field frequency.

Index hex Sub- Data index str. Ce-typical Drive System motor filter or sine filter. DP parameter setting channel 3.

This resistor is integrated in the bus connection plug. Settings for the master Most of the controller manufacturers demand a controller description file controller master data file.

Configuration | Lenze EDSU-REG User Manual | Page /

Parameters tan be absolute or relative values of a physical unit e. This equipment can endanger life through rotating machinery and high voltages, therefore it is essential lemze guards for both electrical and mechanical parts are not removed.

To locate information on specific topics, simply refer to the table of contents at the beginning and to the index at the end of the Operating Instructions.


Display Of Actual Valuesact.

Lenze IB : Manual

All Lenze code numbers begin with 0. Ce-typical Drive System Mankal Dc-injection Brake S Data Data Data tr. Adjustment Of The Dancer-position Controller Set parameter code set L-C to Accessories Accessories are not included in the scope of supply. The data structure is the same for input and output data, see following tables. Accessories Accessories Accessories are not included in the scope of supply.

Value Gain Adjustment of the act. A closed-loop Speed control is to be used, for which a DC tacho serves as act. Dancer-Position control Dancer-Position control with and without diameter Pilot control of centre winder textiles, foils, Paper, ribbon to one shaft is possible Dancer-Position control for surface winders centre winderkiancer-controller surface centre winder tandem winder.

Lenze data types The possible Lenze parameters with their ranges are listed in the corresponding operating instructions. 800 protecting fuses for recommended – 03 Controller type Rated fuse current 2 0 A 3 5 A 5 0 A 16 mm2 Cable Cross-sectlon 4 mm2 6 6 1 2 6 6 1 4 8 6 1 5 Controller type 6 3 A A The controller is inhibited RSP and waits for command 3 switch on.

With terminal control, the active JOG frequency is displayed under co4. These operating instructions are valid for the interface modules as of nameplate designation: Zinc-coated mounting plates allow a permanent contact.

DP process data Process data are data memories where several individual parameters are combined to form a new parameter, the process data. The motor filter reduces capacitive currents caused by parasitic cable manaul.

Lenze 8600 series Manuals

Enabling the additional acceleration and deceleration times With terminal control activate the assigned digital inputs according to the table below. Parameter value or fault information in case of an invalid access.

These Operating Instructions use a series of different Symbols to provide quick reference and to highlight important items. The IB bus interface module has the following features: Parameter Acceptance see Your page settings Preselection: Checking the mains rectifier Disconnect controller from the mains and wait until the DC bus has discharged approx.


lsnze Programming of the freely assignable inputs and Most of the elnze and outputs of the frequency controller are freely assignable via their own Codes, i. Winding with diameter detection and dancer Process output data enable hex Inhibiting and enabling of process output data output data of the master.

Your manual failed to upload Page 28 Installation Connect the Controller, mains fitter, and mains Choke to the grounded mounting plate. For this, the torque setpoint is entered via an analog Signal input which is permanently compared with the torque supplied to the motor shaft.

Accessories For Networking Now you have access to the extended parameter set using the keypad. Calculate the required act. Connecting elements for Optical fibre cables-LECOM-LI Lenze offer a series of specially designed connection accessories for the controllers, in Order to use the fibre optic communication bus.

Select code CO03 and save your Parameter set for example Enter all settings for another application e. Lenze code addressing The access to Lenze parameters is possible. Notes about restrictions of DP functions in the operating mode mixed operation are given on page